Skip to content
Rago CB Antenna Mount For 4Runner (2010-2024)

Rago CB Antenna Mount For 4Runner (2010-2024)

2 reviews
$69.95
In Stock: 5 Available

Product Description

You wanted simple mounting solutions for your antennas and whip flag pole, and we responded with a big 10-4! With the Rago Fabrication Antenna Mount, you get the best of both worlds with our sleek yet rugged stainless steel design. Designed to fit your vehicle flush to create a non intrusive mount for your antenna that you will be proud to show off. Easy install, long lasting, and a no rust guarantee, you will be nothing but pleased with this product!

IN STOCK, READY TO SHIP! NO LEAD TIME

EXPERIENCE THE RAGO DIFFERENCE

The Rago Fabrication CB Antenna Mount is a simple way to mount your CB Antenna on the rear bumper of a  2010-2024 5th Gen Toyota 4Runner using pre-installed rivet nuts and a support plate. 

  • 3/16" Stainless Steel, Rust Free
  • Powder Coated Textured Black
  • All Hardware is Included
  • Requires Drilling
  • Made in America
  • Designed by Rago Fabrication - Veteran Family Owned Business 

 Hole Dimension: 1/2"

Customer Reviews
3.8 Based on 4 Reviews
5 ★
50% 
2
4 ★
25% 
1
3 ★
0% 
0
2 ★
0% 
0
1 ★
25% 
1
Write a Review Ask a Question

Thank you for submitting a review!

Your input is very much appreciated. Share it with your friends so they can enjoy it too!

Filter Reviews:
TC
12/24/2024
Talmage C.
United States

Good cb antenna mount with some work

After alot of trial and error I can say that this mount DOES work for cb antenna. You HAVE to make sure you ground the powder coating off where the antenna stud grounds (usually on the underside of the bracket where the antenna is), you have to remove the powder coat from one of the bolts that sandwich the bumper (I chose the middle one and used a stainless bolt and a stainless washer). Then finally you have to run a piece of 1/2" or bigger braid (it has to be flat braid to properly carry rf) and run that from the small hole on the bracket that's INSIDE the back of the bumper to the frame and/or the body. I did both using a self tap stainless bolt through the frame and then again to a bolt next to the spare tire (so that your ground is running to the frame AND the body). With all this done I have a good swr on channel 20 of 1.2 (also DO NOT install the washer on the top three of the bolts or it will hit your hatch and chip your paint. I opted not to run a washer on the top most and bottom most bolt and only one in the middle to get a good ground. That way it doesn't look funny. Personally I think if rago is going to offer this mount as an antenna mount it should come with the rf strap (3 pack on Amazon was under 10 dollars), the powder coat should be removed in the proper areas to prevent confusion, and one of the included bolts and washers should be stainless. Either that or detailed instructions provided like I just suggested. The big one is that the bracket should be counter sunk and use flush mount bolts to prevent paint damage to the hatch.

Rago CB Antenna Mount For 4Runner (2010-2024)
Was this helpful?  0    0
KK
10/30/2023
Kyle K.
United States

Wrong product twice

Ordered this for my 4runner and received the wrong one. Was sent out another one to receive the exact same wrong item again.

Rago CB Antenna Mount For 4Runner (2010-2023)
Was this helpful?  0    0
RM
01/19/2023
Russell M.
United States

Another great add for your 4runner

Great product if you have a Weboost antenna on a TRDPro 5th gen! The only recommendation is to remove the tail light housing for installation as going underneath is problematic due to interference from the bumper mounts.

Rago Toyota 4Runner CB Antenna Mount (2010-2023)
Was this helpful?  3    0
CT
04/07/2022
Caitlin T.
United States

Good

It’s good but need t ground this mount or your cb won’t work since it’s not attached to metal

Rago Toyota 4Runner CB Antenna Mount (2010-2022)
Was this helpful?  5    0